Dr. Adeel H. Suhail

CHIEF ENGINEER
Baghdad Oil Training Institute, Iraq


Highest Degree
Ph.D. in Advanced Manufacturing Technology from Universiti Putra Malaysia, Malaysia

Share this Profile

Biography

Dr. Eng. Adeel H Suhail, is currently a head of Quality Management Division at Baghdad Oil Training Institute (BOTI), which belong to ministry of oil in Iraq, and a head of Strategic Studies Division at Iraqi Thought Center for Energy Studies (ITCES) which belong to Petroleum Research and Development Center (PRDC) as a first Think Tank Center in Oil and Gas Industry in Iraq. Dr. Adeel has more than 10 scientific papers and projects either presented or published and evaluates more than 10 research paper for different scientific research journals as reviewer. He has a good experience as a curriculum designer when he work for more than 7 years in curriculum and examination department in (BOTI). Dr. Adeel tought different subjects in mechanical and manufacturing engineering field in University of Technology, University Putra Malaysia, and in BOTI he tought many subjects for various disciplines such as oil pipeline division, manufacturing division, vehicle and heavy equipment`s division. Dr. Adeel holds a BSc. in Mechanical Engineering , and MSc. in Mechanical Engineering/ Applied Mechanic from University of Technology/Baghdad, and Doctorate of Philosophy in Mechanical and Manufacturing Engineering/ Advanced Manufacturing Technology from University Putra Malaysia/ Malaysia.

Area of Interest:

Physical Science Engineering
Manufacturing Engineering
Artificial Intelligence
Optimzation
Quality Control

Selected Publications

  1. Suhail, A.H., N. Ismail, S.V. Wong and N.A. Abdul Jalil, 2012. Surface roughness identification using the grey relational analysis with multiple performance characteristics in turning operations. Arabian J. Sci. Eng., 37: 1111-1117.
    CrossRef  |  Direct Link  |  

  2. Kidhir, B.A., B. Mohammed, A.H. Suhail and N. Ismail, 2012. Investigating the influence of approach angle for ceramic cutting tools on chip formation during turning. Arabian J. Sci. Eng., 37: 793-802.
    CrossRef  |  Direct Link  |  

  3. Suhail, A.H., N. Ismail, S.V. Wong and N.A. Abdul Jalil, 2011. Workpiece surface temperature for in-process surface roughness prediction using response surface methodologyac. J. Applied Sci., 11: 308-315.
    CrossRef  |  

  4. Suhail, A.H., N. Ismail, S.V. Wong and N.A. Abdul Jalil, 2011. Single input multi output adaptive network based fuzzy inference system for machinability data selection in turning operations. Adv. Mater. Res., 383-390: 1062-1070.
    CrossRef  |  Direct Link  |  

  5. Suhail, A.H., N. Ismail, S.V. Wong and N.A. Abdul Jalil, 2011. Cutting parameters identification using multi adaptive network based Fuzzy inference system: An artificial intelligence approach. Acad. J. Scient. Res. Essays, 6: 187-195.
    Direct Link  |  

  6. Suhail, A.H., N. Ismail and N.A. Abdul Jalil, 2011. In-process surface roughness prediction using heat generation rate of workpiece surface in turning operation. IOP Conf. Series: Mater. Sci. Eng., 17: 1-10.
    CrossRef  |  Direct Link  |  

  7. Al-Mulla, E.A.J., A.H. Suhail and S.A. Aowda, 2011. New biopolymer nanocomposites based on epoxidized soybean oil plasticized poly(lactic acid)/fatty nitrogen compounds modified clay: Preparation and characterization. Indust. Crops Prod., 33: 23-29.
    CrossRef  |  Direct Link  |  

  8. Suhail, A.H., N. Ismail, S.V. Wong and N.A. Abdul Jalil, 2010. Optimization of cutting parameters based on surface roughness and assistance of workpiece surface temperature in turning process. Am. J. Eng. Applied Sci., 3: 102-108.
    CrossRef  |  Direct Link  |