Dr. Mohammad Azadi

Associate Professor
Faculty of Mechanical Engineering, Semnan University, Iran.

Highest Degree
Ph.D. in Aeronautical and Mechanical Engineering from Sharif University of Technology, Iran

My URL
https://livedna.org/98.33363

Share this Profile

Area of Interest:

Engineering

Selected Publications

  1. Zhao, J., B. Li, Y. Zheng, M. Azadi and X. Chen, 2022. Cyclic deformation behavior and failure mechanism of 316LN stainless steel under creep-fatigue loading at 550 °C. J. Mater. Eng. Perform., 31: 8314-8326.
    CrossRef  |  Direct Link  |  

  2. Parast, M.S.A., A. Bagheri, A. Kami, M. Azadi and V. Asghari, 2022. Bending fatigue behavior of fused filament fabrication 3D-printed ABS and PLA joints with rotary friction welding. Prog. Addit. Manuf., 7: 1345-1361.
    CrossRef  |  Direct Link  |  

  3. Parast, M.S.A. and M. Azadi, 2022. Effect of nano-clay particles and heat treating on pure and fretting fatigue properties of piston aluminum alloy under stress-controlled cyclic bending loading. J. Mater. Eng. Perform., 31: 5927-5942.
    CrossRef  |  Direct Link  |  

  4. Oliya, A.Y.P., M. Azadi, M.S.A. Parast and M. Mokhtarishirazabad, 2022. Effect of heat-treating on microstructure and high cycle bending fatigue behavior of AZ91 and AZE911 magnesium alloys. Adv. Mater. Sci. Eng., Vol. 2022. 10.1155/2022/4030062.
    CrossRef  |  Direct Link  |  

  5. Mohammadi, F., M. Azadi and M.S.A. Parast, 2022. Influence of specimen geometry and notch on fatigue lifetime and fracture behavior of aluminum-based nanocomposite under stress-controlled fully-reversed bending loads. Recent Pat. Nanotechnol., Vol. 16. 10.2174/1872210516666220817115300.
    CrossRef  |  Direct Link  |  

  6. Miri, S.E., M. Azadi and S. Pakdel, 2022. Development of a duty cycle with K-means clustering technique for hydraulic steering in an instrumented TIBA vehicle. Transp. Eng., Vol. 8. 10.1016/j.treng.2022.100114.
    CrossRef  |  Direct Link  |  

  7. Hosseini, S.M., M. Azadi, A. Ghasemi-Ghalebahman and S.M. Jafari, 2022. Data analysis of striation spacing, lifetime, and crack length in crankshaft ductile cast iron under cyclic bending loading through high-cycle fatigue regime. Data Brief, Vol. 45. 10.1016/j.dib.2022.108666.
    CrossRef  |  Direct Link  |  

  8. Farokhpour, M., M.S.A. Parast and M. Azadi, 2022. Evaluation of hardness and microstructural features in piston aluminum-silicon alloys after different ageing heat treatments. Res. Mater., Vol. 16. 10.1016/j.rinma.2022.100323.
    CrossRef  |  Direct Link  |  

  9. Esfarjani, S.M., A. Dadashi and M. Azadi, 2022. Topology optimization of additive-manufactured metamaterial structures: A review focused on multi-material types. Forces Mech., Vol. 7. 10.1016/j.finmec.2022.100100.
    CrossRef  |  Direct Link  |  

  10. Dadashi, A. and M. Azadi, 2022. Experimental bending fatigue data of additive-manufactured PLA biomaterial fabricated by different 3d printing parameters. Preprints, Vol. 2022. 10.20944/preprints202201.0252.v1.
    CrossRef  |  Direct Link  |  

  11. Dadashi, A. and M. Azadi, 2022. Experimental bending fatigue data of additive-manufactured PLA biomaterial fabricated by different 3D printing parameters. Prog. Addit. Manuf., Vol. 2022. 10.1007/s40964-022-00327-1.
    CrossRef  |  Direct Link  |  

  12. Basiri, A., F. Zaïri, M. Azadi and A. Ghasemi-Ghalebahman, 2022. Micromechanical constitutive modeling of tensile and cyclic behaviors of nano-clay reinforced metal matrix nanocomposites. Mech. Mater., Vol. 168. 10.1016/J.MECHMAT.2022.104280.
    CrossRef  |  Direct Link  |  

  13. Bagheri, A., M.S.A. Parast, A. Kami, M. Azadi and V. Asghari, 2022. Fatigue testing on rotary friction-welded joints between solid ABS and 3D-printed PLA and ABS. Eur. J. Mech.- A/Solids, Vol. 96. 10.1016/J.EUROMECHSOL.2022.104713.
    CrossRef  |  Direct Link  |  

  14. Azar, R.G., M.S.A. Parast and M. Azadi, 2022. Heat-treating and nano-reinforcing improvements on fretting fatigue properties and fracture behaviors of cylinder head aluminum alloys. J. Mater. Res. Technol., 20: 1927-1939.
    CrossRef  |  Direct Link  |  

  15. Azadi, M., M.S.A. Parast and M. Azadi, 2022. Effects of plasma nitriding process on the corrosion behavior of GJS700 nodular cast iron. Surf. Topogr.: Metrol. Prop., Vol. 10. 10.1088/2051-672X/ac68fc.
    CrossRef  |  Direct Link  |  

  16. Azadi, M., K. Ivanov, S. Rezanezhad and S.A.A. Talesh, 2022. Scanning and transmission electron microscopy analysis for surface-modified AM60 magnesium alloy by pulsed electron beam irradiation. Nucl. Instrum. Methods Phys. Res., Sect. B, 513: 9-13.
    CrossRef  |  Direct Link  |  

  17. Azadi, M., H. Bahmanabadi, F. Gruen, G. Winter and B. Seisenbacher, 2022. Cyclic hardening/softening experimental data in nano-clay-composite and aluminum alloy under high-temperature strain-controlled loading. Exp. Results, Vol. 3. 10.1017/exp.2021.32.
    CrossRef  |  Direct Link  |  

  18. Azadi, M., A. Shahsavand and M.S.A. Parast, 2022. Analyzing experimental data from reciprocating wear testing on piston aluminum alloys, with and without clay nano-particle reinforcement. Data Brief, Vol. 45. 10.1016/j.dib.2022.108766.
    CrossRef  |  Direct Link  |  

  19. Azadi, M., 2022. A Perspective on metamaterials for the biomechanics application: Multi-material metamaterial (4M) structures. Mater. Sci. Forum, 1064: 151-156.
    CrossRef  |  Direct Link  |  

  20. Azadi, M. and M.S.A. Parast, 2022. Data analysis of high-cycle fatigue testing on piston aluminum-silicon alloys under various conditions: Wear, lubrication, corrosion, nano-particles, heat-treating, and stress. Data Brief, Vol. 41. 10.1016/j.dib.2022.107984.
    CrossRef  |  Direct Link  |  

  21. Azadi, M. and M. Azadi, 2022. Data analysis for investigating the tribological behaviors of aluminum-silicon alloys. Data Brief, Vol. 42. 10.1016/J.DIB.2022.108260.
    CrossRef  |  Direct Link  |  

  22. Azadi, M. and A. Dadashi, 2022. Experimental fatigue dataset for additive-manufactured 3D-printed Polylactic acid biomaterials under fully-reversed rotating-bending bending loadings. Data Brief, Vol. 41. 10.1016/j.dib.2022.107846.
    CrossRef  |  Direct Link  |  

  23. Aroo, H., M. Azadi and M. Azadi, 2022. Corrosion effects on high-cycle fatigue lifetime and fracture behavior for heat-treated aluminum-matrix nano-clay-composite compared to piston aluminum alloy. Silicon, 14: 3749-3763.
    CrossRef  |  Direct Link  |  

  24. Zolfaghari, M., M. Azadi and M. Azadi, 2021. Characterization of high-cycle bending fatigue behaviors for piston aluminum matrix siO2 nano-composites in comparison with aluminum–silicon alloys. Int. J. Metalcast., Vol. 15. 10.1007/s40962-020-00437-y.
    CrossRef  |  Direct Link  |  

  25. Saeedi, M., M. Azadi, M. Mokhtarishirazabad and P. Lopez‐Crespo, 2021. Numerical simulations of carbon/epoxy laminated composites under various loading rates, comparing extended finite element method and cohesive zone modeling. Mater. Design Process. Commun., Vol. 3. 10.1002/mdp2.198.
    CrossRef  |  Direct Link  |  

  26. Rezanezhad, S., M. Azadi and M. Azadi, 2021. Influence of heat treatment on high-cycle fatigue and fracture behaviors of piston aluminum alloy under fully-reversed cyclic bending. Met. Mater. Int., 27: 860-870.
    CrossRef  |  Direct Link  |  

  27. Parast, M.S.A., M.J. Khameneh, M. Azadi, M. Azadi, M.H. Mahdipanah and S. Roostaie, 2021. Effect of plasma nitriding on high-cycle fatigue properties and fracture behaviors of GJS700 nodular cast iron under cyclic bending loading. Fatigue Fract. Eng. Mater. Struct., 44: 2070-2086.
    CrossRef  |  Direct Link  |  

  28. Motamedi, M., G. Shafabakhsh and M. Azadi, 2021. Evaluation of fatigue and rutting properties of asphalt binder and mastic modified by synthesized polyurethane. J. Traffic Transp. Eng. (English Edition), 8: 1036-1048.
    CrossRef  |  Direct Link  |  

  29. Mohammad Azadi, Hanieh Aroo 2021. Bending cyclic behavior and scatter-band analysis of aluminum alloys under beneficial and detrimental conditions through high-cycle fatigue regime. Fract. Struct. Integrity, 15: 272-281.
    CrossRef  |  Direct Link  |  

  30. Khisheh, S., K. Khalili, M. Azadi and V.Z. Hendouabadi, 2021. Influences of roughness and heat treatment on high-cycle bending fatigue properties of A380 aluminum alloy under stress-controlled cyclic loading. Mater. Chem. Phys., Vol. 264. 10.1016/J.MATCHEMPHYS.2021.124475.
    CrossRef  |  Direct Link  |  

  31. Hosseini, S.M., A. Ghasemi-Ghalebahman, M. Azadi and S.M. Jafari, 2021. Crack initiation detection in crankshaft ductile cast iron based on information entropy of acoustic emission signals under tensile loading. Eng. Fail. Anal., Vol. 127. 10.1016/J.ENGFAILANAL.2021.105547.
    CrossRef  |  Direct Link  |  

  32. Golshan, A.M.A., H. Aroo and M. Azadi, 2021. Sensitivity analysis for effects of heat treatment, stress, and temperature on AlSi12CuNiMg aluminum alloy behavior under force-controlled creep loading. Appl. Phys. A, Vol. 127. 10.1007/s00339-020-04134-9.
    CrossRef  |  Direct Link  |  

  33. Esfarjani, S.M., M. Azadi, M. Alizadeh and H. Sayar, 2021. Prediction of fiber breakage and matrix cracking in polymeric composites under low-cycle fatigue regimes by fuzzy and wavelet clustering of acoustic emission signals. Compos.: Mech. Comput. Appl.: Int. J., 12: 17-51.
    CrossRef  |  Direct Link  |  

  34. Esfarjani, S.M., M. Azadi, M. Alizadeh and H. Sayar, 2021. Prediction of fiber breakage and matrix cracking in polymeric composites under low-cycle fatigue regimes by fuzzy and wavelet clustering of acoustic emission signals. Comp. Mech. Comput. Appl. Int. J., 12: 17-51.
    CrossRef  |  Direct Link  |  

  35. Azadi, M., M. Zomorodipour and A. Fereidoon, 2021. Sensitivity analysis of mechanical properties and ductile/brittle behaviors in aluminum-silicon alloy to loading rate and nano-particles, considering interaction effects. Eng. Rep., Vol. 3. 10.1002/eng2.12341.
    CrossRef  |  Direct Link  |  

  36. Azadi, M., M. Samiee and S.M. Esfarjani, 2021. Estimation of low-cycle fatigue lifetime in aluminum-silicon-magnesium alloy of cylinder heads based on striation marks as failure features of fracture surfaces and Paris crack growth law. J. Fail. Anal. Preven., 21: 1466-1475.
    CrossRef  |  Direct Link  |  

  37. Azadi, M., M. Samiee and S.M. Esfarjani, 2021. Correction to: estimation of low-cycle fatigue lifetime in aluminum-silicon-magnesium alloy of cylinder heads based on striation marks as failure features of fracture surfaces and paris crack growth law. J. Fail. Anal. Preven., Vol. 21. 10.1007/s11668-021-01247-y.
    CrossRef  |  Direct Link  |  

  38. Azadi, M., M. Alizadeh, S.M. Jafari and A. Farrokhabadi, 2021. Cumulative acoustic emission energy for damage detection in composites reinforced by carbon fibers within low-cycle fatigue regime at various displacement amplitudes and rates. Polym. Polym. Compos., 29: S36-S48.
    CrossRef  |  Direct Link  |  

  39. Azadi, M., H. Aroo, M. Azadi and M.S.A. Parast, 2021. Comparing of high-cycle fatigue lifetimes in un-corroded and corroded piston aluminum alloys in diesel engine applications. Arch. Foundry Eng., 21: 89-94.
    CrossRef  |  Direct Link  |  

  40. Azadi, M., A. Dadashi, S. Dezianian, M. Kianifar, S. Torkaman and M. Chiyani, 2021. High-cycle bending fatigue properties of additive-manufactured ABS and PLA polymers fabricated by fused deposition modeling 3D-printing. Forces Mech., Vol. 3. 10.1016/j.finmec.2021.100016.
    CrossRef  |  Direct Link  |  

  41. Azadi, M., A. Behmanesh and H. Aroo, 2021. Creep behaviors at 275°C for aluminum-matrix nano-composite under different stress levels. Eng. Fail. Anal., 21: 81-89.
    CrossRef  |  Direct Link  |  

  42. Azadi, M., A. Basiri, A. Dadashi, G. Winter, B. Seisenbacher and F. Grün, 2021. Effect of nano-clay addition and heat-treatment on tensile and stress-controlled low-cycle fatigue behaviors of aluminum-silicon alloy: Effect of nano-clay addition and heat-treatment. Fract. Struct. Integrity, 15: 373-397.
    CrossRef  |  Direct Link  |  

  43. Ahadi, F., M. Azadi, M. Biglari and S.N. Madani, 2021. Study of coating effects on the performance of Stirling engine by non-ideal adiabatic thermodynamics modeling. Energy Rep., 7: 3688-3702.
    CrossRef  |  Direct Link  |  

  44. Motamedi, M., G. Shafabakhsh and M. Azadi, 2020. Evaluating fatigue-damage of asphalt binder and mastic modified with nano-silica and synthesized polyurethane using VECD method. J. Mater. Civ. Eng., 10.1061/(ASCE)MT.1943-5533.0003280.
    CrossRef  |  Direct Link  |  

  45. Sayar, H., M. Azadi and M. Alizadeh, 2019. Detection of crack initiation and propagation in aluminum alloy under tensile loading, comparing signals acquired by acoustic emission and vibration sensors. J. Nondestruct. Eval., 10.1007/s10921-019-0639-9.
    CrossRef  |  Direct Link  |  

  46. Rezanezhad, S., M. Azadi, M. Azadi, 2019. Influence of heat treatment on high-cycle fatigue and fracture behaviors of piston aluminum alloy under fully-reversed cyclic bending. Met. Mater. Int., 10.1007/s12540-019-00498-7.
    CrossRef  |  Direct Link  |  

  47. Azadi, m., M. Saeedi, M. Mokhtarishirazabad and P. Lopez-Crespo, 2019. Effects of loading rate on crack growth behavior in carbon fiber reinforced polymer composites using digital image correlation technique. Compos. Part B: Eng., 10.1016/J.COMPOSITESB.2019.107161.
    CrossRef  |  Direct Link  |  

  48. Azadi, M. and H. Aroo, 2019. Creep properties and failure mechanisms of aluminum alloy and aluminum matrix silicon oxide nano-composite under working conditions in engine pistons. Mater. Res. Express, 10.1088/2053-1591/ab455f.
    CrossRef  |  Direct Link  |  

  49. Sayar, H., M. Azadi, A. Ghasemi-Ghalebahman and S.M. Jafari, 2018. Clustering effect on damage mechanisms in open-hole laminated carbon/epoxy composite under constant tensile loading rate, using acoustic emission. Compos. Struct., 204: 1-11.
    CrossRef  |  Direct Link  |  

  50. Safarloo, S., F. Loghman, M. Azadi and M. Azadi, 2018. Optimal design experiment of ageing time and temperature in inconel-713C superalloy based on hardness objective. Trans. Indian Inst. Met., 71: 1563-1572.
    CrossRef  |  Direct Link  |  

  51. Mohammad Azadi, M., and M. Farzannasab, 2018. Evaluation of high-cycle fatigue behavior in compact bones at different loading frequencies. Meccanica, 53: 3517-3526.
    CrossRef  |  Direct Link  |  

  52. Khameneh, M.J. and M. Azadi, 2018. Reliability prediction, scatter-band analysis and fatigue limit assessment of high-cycle fatigue properties in EN-GJS700-2 ductile cast iron. MATEC Web Conf., 10.1051/MATECCONF/201816510012.
    CrossRef  |  Direct Link  |  

  53. Bahmanabadi, H., S. Rezanezhad, M. Azadi and M. Azadi, 2018. Characterization of creep damage and lifetime in Inconel-713C nickel-based superalloy by stress-based, strain/strain rate-based and continuum damage mechanics models. Mater. Res. Express., 10.1088/2053-1591/aaab04.
    CrossRef  |  Direct Link  |  

  54. Azadi, M., S. Safarloo, F. Loghman and R. Rasouli, 2018. Microstructural and thermal properties of piston aluminum alloy reinforced by nano-particles. AIP Conference Proceedings, January 10, 2018, Author(s) pp: 020027-020027.
    CrossRef  |  Direct Link  |  

  55. Azadi, M., M. Zolfaghari, S. Rezanezhad and M. Azadi, 2018. Effects of SiO2 nano-particles on tribological and mechanical properties of aluminum matrix composites by different dispersion methods. Appl. Phys. A, 10.1007/S00339-018-1797-9.
    CrossRef  |  Direct Link  |  

  56. Azadi, M., H, Sayar, A. Ghasemi-Ghalebahman and S.M. Jafari, 2018. Tensile loading rate effect on mechanical properties and failure mechanisms in open-hole carbon fiber reinforced polymer composites by acoustic emission approach. Compos. Part B: Eng., 158: 448-458.
    CrossRef  |  Direct Link  |  

  57. Khameneh, M.J. and M. Azadi, 2017. Evaluation of high-cycle bending fatigue and fracture behaviors in EN-GJS700-2 ductile cast iron of crankshafts. Eng. Fail. Anal., 85: 189-200.
    CrossRef  |  Direct Link  |  

  58. Azadi, M., and M. Azadi, 2017. Evaluation of high-temperature creep behavior in Inconel-713C nickel-based superalloy considering effects of stress levels. Mater. Sci. Eng.: A 689: 298-305.
    CrossRef  |  Direct Link  |  

  59. Azadi, M., A. Marbout, S. Safarloo, M. Azadi, M. Shariat and M.H. Rizi, 2017. Effects of solutioning and ageing treatments on properties of Inconel-713C nickel-based superalloy under creep loading. Mater. Sci. Eng.: A, 711: 195-204.
    CrossRef  |  Direct Link  |  

  60. Azadi, M., 2016. Failure analysis and prevention in powertrain systems. In: Handbook of Materials Failure Analysis with Case Studies from the Aerospace and Automotive Industries, Makhlouf, A.S.H. and M. Aliofkhazraei (Eds.), Elsevier, Amsterdam, ISBN: 978-0-12-800950-5, Pages: 471-492.
    CrossRef  |  Direct Link  |  

  61. Azadi, M., 2016. Cyclic thermo-mechanical stress, strain and continuum damage behaviors in light alloys during fatigue lifetime considering heat treatment effect. Int. J. Fatigue, 99: 303-314.
    CrossRef  |  Direct Link  |  

  62. Rad, M.R., G.H. Farrahi, M. Azadi and M. Ghodrati, 2015. Stress analysis of thermal barrier coating system subjected to out-of-phase thermo-mechanical loadings considering roughness and porosity effect. Surf. Coat. Technol., 262: 77-86.
    CrossRef  |  Direct Link  |  

  63. Felfeli, M., M. Azadi and G.H. Farrahi, 2015. Constitutive modeling of elastic-visco-plastic behaviors in aluminum alloys subjected to cyclic loadings at various strain rates. J. Strain Anal. Eng. Des., 50: 103-124.
    CrossRef  |  Direct Link  |  

  64. Azadi, M., G.H. Farrahi, G. Winter, P. Huter and W. Eichlseder, 2015. Damage prediction for un-coated and coated aluminum alloys under thermal and mechanical fatigue loadings based on a modified plastic strain energy approach. Mater. Design, 66: 587-595.
    CrossRef  |  Direct Link  |  

  65. Azadi, M., G. Winter, G.H. Farrahi and W. Eichlseder, 2015. Comparison between isothermal and non-isothermal fatigue behavior in a cast aluminum-silicon-magnesium alloy. Strength Mater., 47: 840-848.
    CrossRef  |  Direct Link  |  

  66. Rad, M.R., G.H. Farrahi, M. Azadi and M. Ghodrati, 2014. Effects of preheating temperature and cooling rate on two-step residual stress in thermal barrier coatings considering real roughness and porosity effect. Ceram. Int., 40: 15925-15940.
    CrossRef  |  Direct Link  |  

  67. Moridi, A., M. Azadi and G.H. Farrahi, 2014. Thermo-mechanical stress analysis of thermal barrier coating system considering thickness and roughness effects. Surf. Coat. Technol., 243: 91-99.
    CrossRef  |  Direct Link  |  

  68. Farrahi, G.H., M. Ghodrati, M. Azadi and M.R. Rad, 2014. Stress–strain time-dependent behavior of A356.0 aluminum alloy subjected to cyclic thermal and mechanical loadings. Mech. Time-Depend. Mater., 18: 475-491.
    CrossRef  |  Direct Link  |  

  69. Farrahi, G.H., A. Shamloo, M. Felfeli and M. Azadi, 2014. Numerical simulations of cyclic behaviors in light alloys under isothermal and thermo-mechanical fatigue loadings. Mater. Design (1980-2015), 56: 245-253.
    CrossRef  |  Direct Link  |  

  70. Azadi, M., M. Ghodrati and G.H. Farrahi, 2014. Experimental and numerical evaluations of stress relaxation in A356 aluminium alloy subjected to out-of-phase thermomechanical cyclic loadings. Mater. High Temp., 31: 204-210.
    CrossRef  |  Direct Link  |  

  71. Azadi, M., G.H. Farrahi, G. Winter and W. Eichlseder, 2014. Thermo-mechanical behaviours of light alloys in comparison to high temperature isothermal behaviours. Mater. High Temp., 31: 12-17.
    CrossRef  |  Direct Link  |  

  72. Azadi, M., 2014. Effect of temperature and gas flux on the mechanical behavior of TiC coating by pulsed DC plasma enhanced chemical vapor deposition. Int. J. Eng., 27: 1243-1250.
    CrossRef  |  Direct Link  |  

  73. Azadi, M. and A.S. Rouhaghdam, 2014. Nanomechanical properties of TiN/TiC multilayer coatings. Strength Mater., 46: 121-131.
    CrossRef  |  Direct Link  |  

  74. Mokhtarishirazabad, M., S.M.A. Boutorabi, M. Azadi and M. Nikravan, 2013. Effect of rare earth elements on high cycle fatigue behavior of AZ91 alloy. Mater. Sci. Eng.: A, 587: 179-184.
    CrossRef  |  Direct Link  |  

  75. Mokhtarishirazabad, M., M. Azadi, G.H. Farrahi, G. Winter and W. Eichlseder, 2013. Improvement of high temperature fatigue lifetime in AZ91 magnesium alloy by heat treatment. Mater. Sci. Eng.: A, 588: 357-365.
    CrossRef  |  Direct Link  |  

  76. Farrahi, G.H., M. Azadi, G. Winter and W. Eichlseder, 2013. A new energy-based isothermal and thermo-mechanical fatigue lifetime prediction model for aluminium-silicon-magnesium alloy. Fatigue Fract. Eng. Mater. Struct., 36: 1323-1335.
    CrossRef  |  Direct Link  |  

  77. Azadi, M., G.H. Farrahi, G. Winter and W. Eichlseder, 2013. Experimental fatigue lifetime of coated and uncoated aluminum alloy under isothermal and thermo-mechanical loadings. Ceram. Int., 39: 9099-9107.
    CrossRef  |  Direct Link  |  

  78. Azadi, M., G.H. Farrahi and A. Moridi, 2013. Optimization of air plasma sprayed thermal barrier coating parameters in diesel engine applications. J. Mater. Eng. Perform., 22: 3530-3538.
    CrossRef  |  Direct Link  |  

  79. Azadi, M., A.S. Rouhaghdam, S. Ahangarani, H.H. Mofidi and M. Valiei, 2013. Mechanical behavior and properties of TiN/TiC coating using PACVD. Adv. Mater. Res., 829: 476-481.
    CrossRef  |  Direct Link  |  

  80. Azadi, M., 2013. Effects of strain rate and mean strain on cyclic behavior of aluminum alloys under isothermal and thermo-mechanical fatigue loadings. Int. J. Fatigue, 47: 148-153.
    CrossRef  |  Direct Link  |  

  81. Azadi, M. and M.M. Shirazabad, 2013. Heat treatment effect on thermo-mechanical fatigue and low cycle fatigue behaviors of A356.0 aluminum alloy. Mater. Design, 45: 279-285.
    CrossRef  |  Direct Link  |  

  82. Mehrabani, M.M., A.A. Jafari and M. Azadi, 2012. Multidisciplinary optimization of a stiffened shell by genetic algorithm. J. Mech. Sci. Technol., 26: 517-530.
    CrossRef  |  Direct Link  |  

  83. Azadi, M., A. Moridi and G.H. Farrahi, 2012. Optimal experiment design for plasma thermal spray parameters at bending loads. Int. J. Surf. Sci. Eng., 6: 3-14.
    CrossRef  |  Direct Link  |  

  84. Azadi, M., A. Mafi, M. Roozban and F. Moghaddam, 2012. Failure analysis of a cracked gasoline engine cylinder head. J. Fail. Anal. Preven., 12: 286-294.
    CrossRef  |  Direct Link  |  

  85. Moridi, A., M. Azadi and G.H. Farrahi, 2011. RETRACTED: Coating thickness and roughness effect on stress distribution of A356.0 under thermo-mechanical loadings. Proc. Eng., 10: 1372-1377.
    CrossRef  |  Direct Link  |  

  86. Damircheli, M. and M. Azadi, 2011. Temperature and thickness effects on thermal and mechanical stresses of rotating FG-disks. J. Mech. Sci. Technol., 25: 827-836.
    CrossRef  |  Direct Link  |  

  87. Azadi, M., 2011. Free and forced vibration analysis of FG beam considering temperature dependency of material properties. J. Mech. Sci. Technol., 25: 69-80.
    CrossRef  |  Direct Link  |  

  88. Azadi, M., M. Shariyat, 2010. Nonlinear transient transfinite element thermal analysis of thick-walled FGM cylinders with temperature-dependent material properties. Meccanica, 45: 305-318.
    CrossRef  |  Direct Link  |  

  89. Azadi, M. and M. Azadi, 2010. Thermoelastic Stresses in FG-Cylinders. In: Heat Transfer - Mathematical Modelling, Numerical Methods and Information Technology, Belmiloudi, A. (Ed.), InTech, London, ISBN: 978-953-307-550-1, Pages: 656.
    CrossRef  |  Direct Link  |  

  90. Azadi, S., M. Azadi and F. Zahedi, 2009. NVH analysis and improvement of a vehicle body structure using DOE method. J. Mech. Sci. Technol., 23: 2980-2989.
    CrossRef  |  Direct Link  |  

  91. Azadi, M., S. Azadi, F. Zahedi and M. Moradi, 2009. Multidisciplinary optimization of a car component under NVH and weight constraints using RSM. Int. Mech. Eng. Congr. Exposition, 15: 315-319.
    CrossRef  |  Direct Link  |  

  92. Azadi, M., S. Azadi, F. Zahedi and M. Moradi, 2009. Multidisciplinary optimization of a car component under NVH and weight constraints using RSM. Int. Mech. Eng. Congr. Exposition, 15: 315-319.
    CrossRef  |  Direct Link  |  

  93. Azadi, M. and M. Damircheli, 2009. Nonlinear thermoelastic stress analysis of the rotating FGM disk with variable thickness and temperature-dependent material properties using finite element method. Int. Mech. Eng. Cong. Exposition, 15: 359-364.
    CrossRef  |  Direct Link  |  

  94. Azadi, M. and M. Azadi, 2009. Nonlinear transient heat transfer and thermoelastic analysis of thick-walled FGM cylinder with temperature-dependent material properties using Hermitian transfinite element. J. Mech. Sci. Technol., 23: 2635-2644.
    CrossRef  |  Direct Link  |  

  95. Azadi, M. and F. Zahedi, 2009. Fatigue analysis of antiroll bar for periodic and random inputs using various theories and introducing a new method. Int. Mech. Eng. Congr. Exposition, 13: 71-76.
    CrossRef  |  Direct Link  |  
Member since June, 2020