Area of Interest:

Physical Science Engineering

100%

Materials Characterization

62%

Computer Aided Design

90%

Materials Processing

75%

Metal Forming

55%

Research Publications in Numbers

Books
0

Chapters
0

Articles
0

Abstracts
0

Selected Publications

Turkoz, M., H.S. Halkaci, M. Halkaci, M. Dilmec, S. Avci and M. Koc, 2016. Design, fabrication, and experimental validation of a warm hydroforming test system. J. Manuf. Sci. Eng., Vol. 138. 10.1115/1.4031498.
CrossRef | Direct Link |
Dilmec, M., E.F. Sukur, H.S. Halkaci, M. Halkaci and M. Turkoz, 2016. Comparison of flow curves of AA 5457-O sheet material determined by hydraulic bulge and tensile tests at warm forming temperatures. J. Test. Eval., 44: 952-966.
CrossRef | Direct Link |
Dilmec, M. and M. Arap, 2016. Effect of geometrical and process parameters on coefficient of friction in deep drawing process at the flange and the radius regions. Int. J. Adv. Manuf. Technol., 86: 747-759.
CrossRef | Direct Link |
Tinkir, M., M. Dilmec, M. Turkoz and H.S. Halkaci, 2015. Investigation of the effect of hydromechanical deep drawing process parameters on formability of AA5754 sheets metals by using neuro-fuzzy forecasting approach. J. Intelligent Fuzzy Syst., 28: 647-659.
CrossRef | Direct Link |
Halkaci, H.S., M. Turkoz and M. Dilmec, 2014. Enhancing formability in hydromechanical deep drawing process adding a shallow drawbead to the blank holder. J. Mater. Process. Technol., 214: 1638-1646.
CrossRef | Direct Link |
Dilmec, M. and H. Arikan, 2014. Effect of solution heat treatment conditions on the mechanical properties and formability for AA 2024 alloy. Appl. Mech. Mater., 686: 3-9.
CrossRef | Direct Link |
Dilmec, M., H.S. Halkaci, F. Ozturk, H. Livatyali and O. Yigit, 2013. Effects of sheet thickness and anisotropy on forming limit curves of AA2024-T4. Int. J. Adv. Manuf. Technol., 67: 2689-2700.
CrossRef | Direct Link |
Dilmec, M., H.S. Halkaci, F. Ozturk and M. Turkoz, 2013. Effect of sheet thickness on anisotropy and thickness distribution for AA2024-T4. Mater. Tehnol. Mater. Technol., 47: 605-610.
Direct Link |
Ozturk, F., H.S. Halkaci, M. Turkoz and M. Dilmec, 2012. Detailed investigation of forming limit determination standards for aluminum alloys. J. Testing Eval., 41: 1-12.
CrossRef | Direct Link |
Dilmec, M., 2012. Numerical investigation of manufacturability of various compound shapes using sheet hydroforming process. Appl. Mech. Mater., 217: 1682-1687.
CrossRef | Direct Link |
Turkoz, M., O. Yigit, M. Dilmec, H.S. Halkaci and B. Daghan, 2011. Numerical and experimental comparison of hemispherical punch stretching test. J. Technol. Plast., 36: 87-95.
Direct Link |
Turkoz, M., M. Dilmec and H.S. Halkaci, 2011. Investigation on earing behavior of AA 2024-T4 and AA 5754-O aluminum alloys. Adv. Mater. Res., 264-265: 12-17.
CrossRef | Direct Link |
Secilmis, A., A.M. Olmez, M. Dilmec, H.S. Halkaci and O. Inan, 2009. Determination of optimal EDM machining parameters for machined pure titanium-porcelain adhesion. Int. J. Adv. Manuf. Technol., 45: 55-61.
CrossRef | PubMed | Direct Link |
Dilmec, M., M. Turkoz and H.S. Halkaci, 2007. Design of stamping and sheet hydroforming test unit. Arch. Mater. Sci., 28: 25-29.